The Wireless Gigabit Alliance (WiGig) is holding its first plugfest on October 24th, with something like 10 companies taking part. The precise readiness of their offering isn’t really known yet, but Dr Ali Sadri, the president and chairman of WiGig, an employee of Intel, says they will try to get out more details as close to the day it happens as possible. WiGig relies on the use of 60 GHz carriers, travelling short distance, some two meters, to connect any high speed device to another in a line of sight, in the same room. It is a relative of the WiFi standard and is being pushed by many of the same companies.
It’s funny, you talk about these standards, argue about them, and write about them and then forget about them and suddenly they’re there. Back in the middle of last year SiBeam, since sold off cheaply to Silicon Image, said that it had WiGig in a hybrid with its existing 60 GHz WirelessHD chip, but nobody seemed it take it too seriously and no products have been announced using it as far as we know.
More recently Atheros has taken the Intel refugee group Wilocity, which was formed to work on WiGig, and dropped its design into one of its own WiFi chips. That was announced back in June ready for sampling offering 2.4 GHz, 5.0 GHz and the Wilocity 60 GHz, all on a single device, the Atheros AR9004TB.
Given that Sadri says that this first plugfest is entirely about the PHYand that MAC testing won’t happen until around May, this makes Atheros very hot to trot, keen to be ahead of the group when the starting gun for products goes off. Early entrants like Atheros could get design wins and get into products as early as Q2 or Q3 of 2012, but anyone that waits for a certification suite and then tests their chips can expect to be targeting Q1 of 2013, says Sadri.
The Atheros partnership with Wilocity had been announced the previous July and it means that video signals can deliver across a room at multi-gigabit data transfer speeds, while the traditional WiFi signals can still work around the whole home with devices like tablets, PCs and smartphones, all from the same part.
It is typical approach of waiting for standards to come out and then jumping on them early, and this could pose a dramatic question for all Consumer Electronics TV makers ‘ whether or not to offer 60GHz WiGig in their TVs. Most of them have publicly supported many standards for TV connectivity, with all of them supporting Ethernet, and Sony for instance also backing both Wireless HD and a rival standard from Amimon called WHDI (not in 60 GHz at all but in WiFi spectrum). It has also expressed some interest in WiGig, but nothing definitive.
Sadri told us, ‘It depends whether we see non-networking devices first or not, because people can come to market with cable replacement strategies for HDMI, and Displayport or Wireless USB connections for things like displays and docking stations. Or they can come out with WiGig access points. We’re not sure what we’re going to see first.
‘The real challenge is getting WiGig into CMOS and then after that volume will dictate pricing. Some people see WiGig used in public places like airports, in the same way as WiFi, but used to drive media hotspots instead of hotspots. This would mean putting them on a 10Gb Ethernet cable and putting four or five WiGig access points around a sitting area, instead of using one overloaded WiFi access point. That could give wide video selection at blazing speeds.’
Sadri explained that to carry video WiGig had so much bandwidth that it could cope with uncompressed video, but the way PC screens are addressed is to offer I-Frames only, with no in between frames, using Profile 44 of the H.264 codec. This would lead to immensely high quality video with little processing at either end needed ‘ certainly less than the compute intensive creation of all the low data delta frames that are usually between I-frames. This type of media hotspot would require at least 4 or 5 chips where WiFi would use one, and lead to a huge amount of chip volume and therefore very low volume pricing.
That’s not the sort of system for delivering TV around a home, more for replacing the video cable to a display, and the new SiBeam owner Silicon Image has already come out with the SiI6300 family of third generation 60 GHz chips which is both a transmitter and receiver set, supporting WirelessHD 1.1 using 1080p/60, 36-bit Deep Color video and all 3D formats.
Back in June Panasonic announced a WiGig implementation optimized for smartphones with a PHY as fast as 7Gbps and real world speeds potentially as high as 90% of that. The idea is to rapidly transfer files to and from a phone and other devices in the home, such as DVRS. So this is a low power version for handsets as an HDMI cable replacement. The company said at the launch that its chips would draw less than one Watt during operation.
So that is likely to be at least three of the chips in the plugfest, but beyond that many others might only be at the FPGA stage and you can take your pick from the other majors that are in the WiGig Alliance such as Intel, NEC, Nokia, Samsung, Toshiba, Texas Instruments, Marvell, Realtek and Broadcom and many others.
Sadri expects the first devices to be operating at about 3 or 4 Gbps on the first cut of the PHY, and then later gradually rise up towards the theoretical maximum of 7 Gbps and to end up being built in 40nm to 45 nm geometry on the eventual chips. But even he is unsure of what type of products we’ll see first.