Your browser is not supported. Please update it.

17 April 2014

New Lantiq FTTdp chip uses 40% less electical power

Lantiq has developed a new version of its Vinax chip for use in tiny, low-power FTTdp (distribution point) boxes. The new one, called Vinax dp, uses 40% less power than Lantiq’s prior low-power Vinax V3 chip. The new Vinax dp chip is capable of an aggregate of 300 Mbps, broken down into 200 Mbps down and 100 Mbps up. Its theoretical speed is 340 Mbps in total so there is still room for faster performance. Vinax dp will be available mid-year ‘ and it samples in June, with volume production planned for August.

The 200 Mbps meets or exceeds the goals that most countries have set for broadband. Lantiq estimates that FTTdp will be equal to somewhere between 5% to 30% of FTTH deployments globally. It should be able to me a lot more specific than that, surely.

The electric power required for the Vinax-based distribution point is so small that the distribution point does not even need a power supply. It gets all the power it needs from a reverse-power modem/gateway in the home. Also existing copper wire connection can be looped through the distribution point so that there is no service disruption during the installation.

What’s most important, according to Lantiq, is that Vinax V3-based systems are ready for volume deployments today and that the new Vinax dp will be available by year end.

It said VDSL FTTdp is the technology for now because it immediately helps telcos upgrade existing broadband networks to ultrafast data today. There’s no need to wait for G.fast. For the fastest copper wire-delivered data rates now, Lantiq said, FTTdp is ‘the weapon of choice’ for telcos who need an immediate although perhaps intermediate step on the way to G.fast. That’s what 300 Mbps VDSL-based FTTdp can provide today. Lantiq did not address the possibility of using G.hn chips in the same way (see previous issues of Faultline).

The Vinax dp chips have passed the test for full interoperability with fiber (GPON gear) and DSL equipment, a very important matter for telcos. The new chips can be used in the same circuit board that was designed for the prior Vinax chip. The new Vinax dp chips need to be attached to fiber within 200 meters of the residence or, in an MDU, installed in the basement.

The power-less installations saves telcos the $1,000 to $2,000 additional it would typically cost them to install fiber to the residence the company claims. Modems/gateways with Vinax dp chips can be shipped to the home for easy installation by the subscriber. There’s no drilling or digging in or outside the subscriber’s premises to bring fiber-like speeds to the subscriber.

Those speeds will allow telcos to compete against the cablecos’ DOCSIS broadband technology, keep government regulators happy and, most importantly, provide the subscriber with all the speed he is likely to need for the next three to five years.

Each distribution point with Vinax dp chips can support up to 16 residences and it eliminates the cost of vectoring and/or bonding because each copper wire from the distribution point is a direct connection to the modem/gateway in the residence. However, the latest version of VDSL ‘ profile 30a ‘ is required for peak speeds. The previous VDSL profile 17 maxes out at 100 Mbps.

Lantiq was the first to market with chips supporting FTTdp. Orange Polska was the first to use them when in January 2014 it began deploying them in boxes from Aethra Telecommunications in Warsaw, Poland.

Interestingly, Orange Polska is 50% owned by France Telecom’s Orange. Orange is rumored to be so pleased with the results in Poland that it plans to deploy FTTdp in France.

Lantiq said that the upcoming G.fast broadband technology for telcos is fully compatible with its FTTdp and they can be integrated into the same network. It said the specifications for G.fast have been frozen and the first G.fast prototypes for trials will be available this fall. Lantiq expects telcos to begin deploying G.fast in small quantities in 2015 and in large quantities in 2016.

Lantiq says it is the main supplier of technology to the ITU T group that’s developing the G.fast standard. It is also developing a complete G.fast reference system for equipment makers including a G.fast circuit board, documentation, software and firmware.