BT has completed its G.fast field test and claims to have reached 1Gbps over a fiber and copper mix. The trial achieved a download speed of 800Mbps and an upload speed of 200Mbps over 19 meters, with 700Mbps/200Mbps over 66 meters. Those speeds will no doubt endear copper to the telco, as it tries to wring out as much life as it can from its existing infrastructure.
The Fiber to the distribution point (FTTdp) model allows BT to lay fiber up to its street furniture from its core distribution network, while leaving the copper that links the street cabinets to the homes intact. Twisted pair copper is the predominant medium in the UK, and up till now has been criticized for its low top speed. The speeds were revealed by Tim Whitley, the Managing Director of Research and Innovation at BT, speaking at Huawei’s Ultra-Broadband Forum in London.
But as the copper is already in place, removing it and replacing it becomes a very costly process – requiring home visits and large volumes of support staff to ensure that the new replacement can be rolled out smoothly. If BT can manage to boost the speed of the copper lines that are already in place, it can offer speeds that rival a FTTH connection without having to pay the expense of actually running fiber into the home.
BT says that its 66 meter 700Mbps/200Mbps result is suitable for 80% of UK homes, and that the speed can be tailored to meet the consumer’s needs, i.e. tiered packages or bandwidth restrictions. Another benefit of this approach is that it can be installed by the customers, who in theory would only have to plug in a freshly provided CPE – which would again save on deployment costs.
Twisted-pair copper’s speed is largely dependent on the length of the cable, with shorter lengths capable of higher bitrates than longer lines. As BT is planning on massively reducing the length of the line from the distribution point to the consumer home, shrinking the last-mile to something more like the last-meters, a number of technologies and approaches can be used to pipe more data down the copper.
However, BT admits that G.fast is an immature technology, with the G.9071 specification due to be approved in December this year, with the entire standard due in 2015. BT is committing to a new ultra-fast broadband lab at its Adastral Park center in Ipswich, and says it will put some of its best minds to the task.
BT is currently using a pre-standard version of Huawei’s G.fast technology, which uses a FPGA (field programmable gate array) instead of a silicon chip – a necessary evil, given that there are currently no G.fast chips on the market. BT chose not to disclose details of the exact hardware and silicon involved to Faultline, but we know several G.fast chips are in development, from the likes of Israeli startup Sckipio (which claims to have contributed 20% of the G.fast standard so far), and almost certainly Ikanos (which would be dead in the water if it doesn’t, but does have a Neos chipset that supports G.fast available to developers) and the so-far silent Broadcom.
Ikanos’ NodeScale vectoring technology is currently used by Huawei and ZTE, and thanks to the deal with Alcatel-Lucent (see separate story) it looks like all Alcatel’s customers will soon likely have access to the Ikanos chips too – likely at the expense of Broadcom’s order sheet. Alcatel has also conducted G.fast trials with Telekom Austria and its subsidiary A1.
G.fast is an evolution of VDSL2, and is currently being defined by the ITU, which envisions the technology only replacing VDSL2 at shorter distances. It uses the same discrete multi-tone (DMT) modulation as most VDSL and ADSL variants, which adapts its transmission to the conditions of the line – meaning it will change carriers if its signal isn’t getting through. Vectoring is still used to compensate for crosstalk between the lines in each local loop, which is much worse in G.fast than in VDSL2.
The same forward error correction technology is used in G.fast as VDSL2. Unlike VDSL2, G.fast doesn’t use frequency division duplex (FDD) modulation. Instead it uses time division duplex modulation (TDD), which uses timeslots instead of frequency bands for the different downstream and upstream transmissions – and is known as synchronous TDD-OFDM technology
The most noticeable difference between G.fast and VDSL2 is seen in the size of the carrier. VDSL2 uses up to 8.5MHz, 17.664MHZ or 30MHz of the available spectrum in a twisted pair line. G.fast is able to use 106MHz and 212MHz profiles, but importantly can be supported at the same time as VDSL or ADSL from the same distribution point – which would allow an operator to easily migrate the local loops spending less capex than if it had to replace the street furniture too. The current industry consensus is that phase 1 of G.fast will use 106MHz before advancing to 212MHz in the second phase rollout.